Eldes ESIM264 Instrukcja Instalacji Strona 18
- Strona / 140
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
18
3. Installation
The system can be installed only in a metal or non-ammable enclosure. When using the metal enclosure it is necessary to ground it
using yellow/green colour cable. For the connection of 230V transformer use 3x0.75 mm
2
1 thread double isolated cable. The primary
circuit of the transformer must be connected through 0.5A fuse. 230V power supply cables must not be grouped with low voltage
cable group. For the connection of power supply and output connectors use 1 thread 2x0.75 mm
2
unshielded cable. For the connec-
tion of zone/PGM output connectors use 0.50 mm
2
1 thread unshielded cable of up to 100 meters length.
1. Place the SIM card into the card holder and make sure that PIN code request is disabled. The PIN code can be disabled by
inserting the SIM card into a mobile phone and following proper menu steps. There must be no SMS messages stored in the
memory. In addition, make sure that the additional services, such as voice mail, call forwarding, report on mised/busy calls
are disabled on the SIM card. For more details, please, contact your GSM operator.
2. Connect the antenna.
3. Install the mini buzzer close to iButton® key reader (if any) in order to hear alarm system arming and disarming countdown
period. A LED can be used in parallel to mini buzzer, or both at once. ED1 is recommended for convenient installation.
4. Wire up the system according to the wiring diagrams. See chapter 2.3 Wiring Diagrams for more details.
5. Connect the resistors and sensors to the system according to one of the selected zone connection types. See chapter 2.3.2
Zone Connection Types for more details.
6. Connect the backup battery and main power supply (transformer).
7. The system starts up in less than a minute. LED PWR indicates main power supply status. LED STATUS should be blinking indicat-
ing successful micro-controller operation. In addition, the system sends an SMS message to a preset User 1 phone number.
8. System is ready for use.
The installation of iButton® key reader, EKB2/EKB3, EWK1 wireless key-fob is not mandatory. However it is recommended
to have those devices installed as an emergency switch in case your mobile phone is switched o or missing.
To increase system reliability, it is recommended not to use prepaid SIM cards. The system would fail to send any messa-
ges upon depletion of prepaid account. In addition it is recommended to disable call forwarding and voice mail feature.
It is highly recommended to choose the same GSM cellular provider both for users and for ESIM264 system in order to
assure fast and reliable SMS message delivery and phone call connection.
Even though alarm system ESIM264 installation process is not too complicated, we still recommend to perform it by a
person with basic knowledge in electrical engineering and electronics to avoid any system damage.
ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G SIM cards and 3G SIM cards with 2G prole
enabled are supported. For more details, please, contact your GSM operator.
- INSTALLATION MANUAL 1
- Contents 3
- Installation Manual v2.2 6
- Limited Liability 7
- Manufacturer Warranty 7
- Package Content 7
- About Installation Manual 7
- 1. General Information 8
- 2. Technical Specications 11
- Fig. No.1 12
- 2.3 Wiring Diagrams 13
- Fig. No. 5 14
- Fig. No. 6 14
- Fig. No. 7 15
- Fig. No. 8 16
- Fig. No. 9 17
- 3. Installation 18
- 4. Operation Description 19
- 4.4 Wireless Devices 21
- 4.5 RS485 Interface 21
- 4.6 1-Wire® Interface 21
- 5. Conguration & Control 23
- CONFIGU 24
- XXXX_STCONFIG 25
- Shut down the 26
- Connection with 26
- Set SMS Language 26
- Set SMS Password 27
- Set User Password 27
- Delete User Password 28
- Replace User Password 28
- Set User Phone 30
- Delete User 30
- List User Phone 31
- Numbers 31
- Set Date & Time 32
- Arm the System 33
- Disarm the System 33
- Enable Arm 34
- Disarm by Zone 34
- Disable Arm 34
- Set Zone Alarm Text 35
- List Violated Zones 35
- Set Entry Delay 36
- List Violated 36
- Set Exit Delay 37
- Enable ATZ Mode 37
- Disable ATZ Mode 37
- - Type 1 38
- - Type 2 38
- - Type 3 38
- - Type 4 38
- - Type 5 38
- Disable Zone 39
- Enable Zone 39
- Bypass Zone 40
- Bypass All Zones 40
- Unbypass Zone 40
- Set Zone Type 41
- Enable Stay Mode 42
- Disable Stay Mode 43
- Activate Stay 43
- Mode Manually 43
- Disable Force Mode 44
- Enable Force Mode 44
- Disable Chime 45
- Enable Chime 46
- List Zone & PGM 46
- Output Status 46
- Set PGM Output Name 47
- Turn ON PGM Output 47
- / Set PGM Output 47
- Startup Status (ON) 47
- Example: 1111_C3:ON:13.23.48 48
- [49xx1#] 49
- [49xx0#] 49
- [3312#] 49
- Disable EPGM8 50
- Module Mode 50
- Set Siren Alarm 50
- Duration 50
- See Siren Alarm 51
- Enable Bell Squawk 51
- Disable Bell Squawk 51
- Info SMS 53
- Set Periodic 53
- Disable Periodic 54
- Disable Call in 54
- Case of Alarm 54
- Enable SMS in Case 61
- Loss/Restore 61
- Set Main Power 61
- Loss Delay 61
- Restore Delay 62
- Remote Listening 62
- Enable Control from 63
- Any Phone Number 63
- Disable Control from 63
- Set Keyboard Partition 64
- Switch Between 64
- Keyboard Partitions 64
- Enable Keyboard 64
- Partition Switch 64
- Set Zone Partition 66
- Set iButton® Partition 66
- Disable Event Log 67
- Enable Event Log 67
- Set Microphone Gain 68
- Set Speaker Level 68
- Reset to Default 69
- Parameters 69
- Menu path: 70
- 6.3 Troubleshooting 74
- 7. Wired Devices 76
- MAIN SCREEN VIEW 82
- DISABLE / ENABLE 85
- PARTITION [0... 1] 85
- 7.2 EKB3 - LED Keyboard 88
- FRONT SIDE 89
- AUX- AUX+ 90
- D1 D2 D3 D4 D5 D6 D7 D8 94
- 7.5 EA1 – Audio Output Module 96
- COM DATA 98
- Enable New iButton® 99
- Key Mode 99
- Disable New 99
- Check iButton® Key ID 100
- Delete iButton® Key ID 100
- Add Wireless Device 101
- Wireless Device Info 103
- Test Wireless Device 103
- EWT1 ESIM264 104
- Wireless Expansion 105
- Module EW1 105
- MAGNET SENSOR 109
- 8.5 EWK1 - Wireless Key-Fob 112
- RESETLED 114
- C1 C2 Z1 Z2 COM 122
- 9. Monitoring Station 124
- Enable Monitoring 125
- Station Mode 125
- Disable Monitoring 125
- Disable Data Message 126
- Enable User Message 127
- Disable User Message 128
- Set Account (Alarm 128
- System ID) 128
- Set Primary 129
- Connection 129
- Set Backup 129
- Connection (-s) 129
- Set Server IP Address 130
- Set Delay after Last 130
- Communication 130
- Set DNS1 Server 131
- IP Address 131
- Set DNS2 Server 131
- Set Server Port 131
- Set Protocol 132
- Set Local Port 132
- Set User 133
- Set Password 133
- Set Prole 133
- Set Unit ID 134
- Set Attempts 134
- Set Monitoring Station 135
- Phone Number 135
- Set Test Period 135
- Delete Monitoring 136
- Station Phone Number 136
- For notes 138
- Made in Lithuania 140
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Eldes ESIM264
(28 strony)
(44 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji