Eldes EKB3 Instrukcja Instalacji Strona 128
- Strona / 168
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
128
128 EN
MANUAL ELDES ESIM264 V3.1
D1
LED
D2
C2
COM
DC+
Z1
C1
Z2
58
+12V
EW1
Power supply
DC+ C1 C2 Z1 Z2 COM
59
32.2.1.2. Connector & LED Functionality
COM Common terminal for power supply, zones
Z2, Z1 Security zone terminals
C2, C1 PGM output terminals
DC+ Positive power supply terminal
D1, D2 Pins for restoring default parameters
LED EW1 status
32.2.2. Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Wire up EW1 as indicated in Fig. No. 59.
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Conguration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. T he system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EW1
closer to ESIM264 alarm system device and bind it again.
5. EW1 module is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.2.4 Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be
0,5 meters.
32.2.3. EW1 Zones, PGM Outputs & Tamper
Upon successful EW1 module binding process, the system adds 2 wireless Instant zones intended for wired sensor connection and 2 wireless
PGM outputs intended for electrical appliance connection and control.
The wireless connection loss between EW1 and ESIM264 alarm system leads to system alarm regardless of system being armed or disarmed.
The system identies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The
SMS text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
32.2.4. Restoring Default Parameters
1. Disconnect EW1 power supply.
2. Short circuit (connect) pins D1 and D2.
3. Power up EW1 and wait until LED provides several short ashes.
4. Disconnect power supply.
5. Remove short-circuit from D1 and D2 pins.
6. Power up EW1.
7. Parameters restored to default.
- INSTALLATION MANUAL 1
- Installation Manual v3.1 2
- Contents 3
- Limited Liability 5
- Manufacturer Warranty 5
- Package Content 5
- About Installation Manual 5
- 1. GENERAL INFORMATION 6
- Ping Period 10
- MANUAL ELDES ESIM264 V3.1 11
- 2. TECHNICAL SPECIFICATIONS 12
- GSM signal strength 13
- SIREN/BELL 14
- Parallel Wiring Method 19
- 3. INSTALLATION 20
- 0.5 m to 30 m 23
- 0.5 m to 150 m 23
- 5. CONFIGURATION METHODS 25
- 6. PASSWORDS 28
- 7. SYSTEM LANGUAGE 29
- 8. USER PHONE NUMBERS 30
- 9. DATE AND TIME 33
- 10. USER PASSWORDS 34
- 11. iBUTTON KEYS 36
- 12. ARMING AND DISARMING 38
- 13. EXIT AND ENTRY DELAY 46
- 14. ZONES 48
- 15. STAY MODE 56
- 16. TAMPERS 57
- 19. WIRELESS DEVICES 67
- 20. SIREN/BELL 71
- 23. PARTITIONS 78
- 24. TEMPERATURE SENSORS 81
- 27. SYSTEM NOTIFICATIONS 86
- 28. EVENT LOG 90
- 30. MONITORING STATION 93
- 31. ELDES WIRED DEVICES 108
- 00:4520,2 109
- Jumper position Address 117
- AUX- AUX+ 118
- D1 D2 D3 D4 D5 D6 D7 D8 122
- AU X- AUX+ 123
- 32. ELDES WIRELESS DEVICES 126
- Power supply 128
- MAX 20 mm 131
- 0-90% RH @ 0... +40 °C 135
- (non-condensing) 135
- RESETLED 136
- C1 C2 Z1 Z2 COM 141
- Battery Voltage 143
- ANYWHERE 144
- IN THIS AREA 144
- Mounting slot 146
- Battery pocket door 146
- Mounting plate 146
- FRONT SIDE 151
- BACK SIDE 151
- Press and hold 152
- Insert a screwdriver or 152
- 20 mm max 153
- FRONT SIDE of ENCLOSURE 156
- MOUNTING POINT A 157
- MOUNTING 157
- 33. REMOTE SYSTEM RESTART 159
- 34. TECHNICAL SUPPORT 160
- 35. RELATED PRODUCTS 164
- DS1990A-F5 - iButton key 165
- 166
- EWS3 - wireless indoor siren 167
- Made in the European Union 168
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Eldes EKB3
(26 strony)
(16 strony)
(44 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji